BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f6b70
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
 *** Possibly defective BIOS detected (irqtable)
 *** Many BIOSes matching this signature have incorrect IRQ routing tables.
 *** If you see IRQ problems, in paticular SCSI resets and hangs at boot
 *** contact your hardware vendor and ask about updates.
 *** Building an SMP kernel may evade the bug some of the time.
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: INTEL    Product ID: Lancewood    APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #0 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat.       Using 1 I/O APICs
Processors: 1
Kernel command line: root=/dev/md2 ro console=tty0 console=ttyS0,115200n8
Initializing CPU#0
Detected 547.185 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1091.17 BogoMIPS
Memory: 515776k/524224k available (1432k kernel code, 8060k reserved, 411k data,
 276k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU:     After generic, caps: 0383fbff 00000000 00000000 00000000
CPU:             Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel Pentium III (Katmai) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 0 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 0 ... ok.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 0-0, 0-9, 0-10, 0-11, 0-16, 0-17, 0-18, 0-20, 0-22, 0-23 n
ot connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 18.
number of IO-APIC #0 registers: 24.
testing the IO APIC.......................

IO APIC #0......
.... register #00: 00000000
.......    : physical APIC id: 00
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 000 00  1    0    0   0   0    0    0    00
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 001 01  0    0    0   0   0    1    1    71
 0d 001 01  0    0    0   0   0    1    1    79
 0e 001 01  0    0    0   0   0    1    1    81
 0f 001 01  0    0    0   0   0    1    1    89
 10 000 00  1    0    0   0   0    0    0    00
 11 000 00  1    0    0   0   0    0    0    00
 12 000 00  1    0    0   0   0    0    0    00
 13 001 01  1    1    0   1   0    1    1    91
 14 000 00  1    0    0   0   0    0    0    00
 15 001 01  1    1    0   1   0    1    1    99
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ19 -> 0:19
IRQ21 -> 0:21
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 547.1997 MHz.
..... host bus clock speed is 99.4905 MHz.
cpu: 0, clocks: 994905, slice: 497452
CPU0<T0:994896,T1:497440,D:4,S:497452,C:994905>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdab0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using BIOS Interrupt Routing Table
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using BIOS for IRQ routing
PCI->APIC IRQ transform: (B0,I9,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 19
PCI->APIC IRQ transform: (B0,I14,P0) -> 21
PCI->APIC IRQ transform: (B0,I18,P3) -> 21
PCI: Cannot allocate resource region 4 of device 00:12.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com>
Starting kswapd
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI IS
APNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
loop: loaded (max 8 devices)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.
html
eepro100.c: $Revision: 1.1 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@sa
w.sw.com.sg> and others
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:D0:B7:7F:F6:5A, IRQ 19.
  Board assembly 729757-006, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
eth1: Intel Corp. 82557/8/9 [Ethernet Pro 100] (#2), 00:D0:B7:65:D1:57, IRQ 21.
  Board assembly 000000-000, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:12.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:pio, hdd:pio
hda: MATSHITA CR-175, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec aic7896/97 Ultra2 SCSI adapter>
        aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec aic7896/97 Ultra2 SCSI adapter>
        aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/253 SCBs

(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
  Vendor: QUANTUM   Model: ATLAS10K2-TY734J  Rev: DDD6
  Type:   Direct-Access                      ANSI SCSI revision: 03
(scsi0:A:1): 80.000MB/s transfers (40.000MHz, offset 127, 16bit)
  Vendor: QUANTUM   Model: ATLAS10K2-TY734J  Rev: DDD6
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled.  Depth 8
scsi0:A:1:0: Tagged Queuing enabled.  Depth 8
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
SCSI device sda: 143443640 512-byte hdwr sectors (73443 MB)
Partition check:
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
SCSI device sdb: 143443640 512-byte hdwr sectors (73443 MB)
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   8regs     :   955.200 MB/sec
   32regs    :   630.000 MB/sec
   pIII_sse  :  1089.200 MB/sec
   pII_mmx   :  1205.600 MB/sec
   p5_mmx    :  1264.000 MB/sec
raid5: using function: pIII_sse (1089.200 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
 [events: 00000026]
 [events: 00000026]
 [events: 00000009]
 [events: 00000009]
 [events: 00000008]
 [events: 00000026]
 [events: 00000026]
 [events: 00000022]
 [events: 00000022]
 [events: 00000021]
md: autorun ...
md: considering sdb7 ...
md:  adding sdb7 ...
md:  adding sda7 ...
md: created md5
md: bind<sda7,1>
md: bind<sdb7,2>
md: running: <sdb7><sda7>
md: sdb7's event counter: 00000021
md: sda7's event counter: 00000008
md: superblock update time inconsistency -- using the most recent one
md: freshest: sdb7
md: kicking non-fresh sda7 from array!
md: unbind<sda7,1>
md: export_rdev(sda7)
md: RAID level 1 does not need chunksize! Continuing anyway.
md5: max total readahead window set to 124k
md5: 1 data-disks, max readahead per data-disk: 124k
raid1: device sdb7 operational as mirror 0
raid1: md5, not all disks are operational -- trying to recover array
raid1: raid set md5 active with 1 out of 2 mirrors
md: updating md5 RAID superblock on device
md: sdb7 [events: 00000022]<6>(write) sdb7's sb offset: 62251776
md: recovery thread got woken up ...
md: recovery thread finished ...
md: considering sdb6 ...
md:  adding sdb6 ...
md:  adding sda6 ...
md: created md4
md: bind<sda6,1>
md: bind<sdb6,2>
md: running: <sdb6><sda6>
md: sdb6's event counter: 00000022
md: sda6's event counter: 00000009
md: superblock update time inconsistency -- using the most recent one
md: freshest: sdb6
md: kicking non-fresh sda6 from array!
md: unbind<sda6,1>
md: export_rdev(sda6)
md: RAID level 1 does not need chunksize! Continuing anyway.
md4: max total readahead window set to 124k
md4: 1 data-disks, max readahead per data-disk: 124k
raid1: device sdb6 operational as mirror 0
raid1: md4, not all disks are operational -- trying to recover array
raid1: raid set md4 active with 1 out of 2 mirrors
md: updating md4 RAID superblock on device
md: sdb6 [events: 00000023]<6>(write) sdb6's sb offset: 2931712
md: recovery thread got woken up ...
md4: no spare disk to reconstruct array! -- continuing in degraded mode
md: recovery thread finished ...
md: considering sdb5 ...
md:  adding sdb5 ...
md:  adding sda5 ...
md: created md3
md: bind<sda5,1>
md: bind<sdb5,2>
md: running: <sdb5><sda5>
md: sdb5's event counter: 00000022
md: sda5's event counter: 00000009
md: superblock update time inconsistency -- using the most recent one
md: freshest: sdb5
md: kicking non-fresh sda5 from array!
md: unbind<sda5,1>
md: export_rdev(sda5)
md: RAID level 1 does not need chunksize! Continuing anyway.
md3: max total readahead window set to 124k
md3: 1 data-disks, max readahead per data-disk: 124k
raid1: device sdb5 operational as mirror 0
raid1: md3, not all disks are operational -- trying to recover array
raid1: raid set md3 active with 1 out of 2 mirrors
md: updating md3 RAID superblock on device
md: sdb5 [events: 00000023]<6>(write) sdb5's sb offset: 497856
md: recovery thread got woken up ...
md3: no spare disk to reconstruct array! -- continuing in degraded mode
md4: no spare disk to reconstruct array! -- continuing in degraded mode
md: recovery thread finished ...
md: considering sdb3 ...
md:  adding sdb3 ...
md:  adding sda3 ...
md: created md2
md: bind<sda3,1>
md: bind<sdb3,2>
md: running: <sdb3><sda3>
md: sdb3's event counter: 00000026
md: sda3's event counter: 00000026
md: RAID level 1 does not need chunksize! Continuing anyway.
md2: max total readahead window set to 124k
md2: 1 data-disks, max readahead per data-disk: 124k
raid1: device sdb3 operational as mirror 0
raid1: device sda3 operational as mirror 1
raid1: raid set md2 active with 2 out of 2 mirrors
md: updating md2 RAID superblock on device
md: sdb3 [events: 00000027]<6>(write) sdb3's sb offset: 4000064
md: sda3 [events: 00000027]<6>(write) sda3's sb offset: 4000064
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1,1>
md: bind<sdb1,2>
md: running: <sdb1><sda1>
md: sdb1's event counter: 00000026
md: sda1's event counter: 00000026
md: RAID level 1 does not need chunksize! Continuing anyway.
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device sdb1 operational as mirror 0
raid1: device sda1 operational as mirror 1
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
md: sdb1 [events: 00000027]<6>(write) sdb1's sb offset: 32000
md: sda1 [events: 00000027]<6>(write) sda1's sb offset: 32000
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,2), internal journal
 [events: 00000086]
 [events: 00000086]
md: autorun ...
md: considering sda2 ...
md:  adding sda2 ...
md:  adding sdb2 ...
md: created md1
md: bind<sdb2,1>
md: bind<sda2,2>
md: running: <sda2><sdb2>
md: sda2's event counter: 00000086
md: sdb2's event counter: 00000086
md: RAID level 1 does not need chunksize! Continuing anyway.
md1: max total readahead window set to 124k
md1: 1 data-disks, max readahead per data-disk: 124k
raid1: device sda2 operational as mirror 1
raid1: device sdb2 operational as mirror 0
raid1: raid set md1 active with 2 out of 2 mirrors
md: updating md1 RAID superblock on device
md: sda2 [events: 00000087]<6>(write) sda2's sb offset: 2000000
md: sdb2 [events: 00000087]<6>(write) sdb2's sb offset: 2000000
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 1999992k swap-space (priority -1)

-- BrianSzymanski - 16 Dec 2003
Topic revision: r1 - 16 Dec 2003, BrianSzymanski
This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding Foswiki? Send feedback